翻板阀、锁风阀、卸灰阀类
钟形卸灰阀

本系列钟形卸灰阀广泛适用于冶金、建材、石化、电力等行业,作为各工业炉窑及除尘系统的卸灰装置。

This series valve is widely used in metallurgy, building material, oil chemical and electric power industries etc. It is the discharging device of stove and removing dust system.

 

结构特点:

Structure characteristic:

该钟形卸灰阀由阀体、锥形阀塞、连杆、驱动装置等组成,用连杆拉动阀塞上下运动完成启闭动作。其中X型为橡胶软密封,应用于冶炼高炉喷煤系统的煤粉输送控制。W型为阀体本体材料密封,应用于除尘系统尘灰输送控制。

This valve is made up of body, cone valve plug, connected pole, driving device etc. The plug drew by the connected pole moves up and down to complete the action of open and close. Type X denotes rubber soft seal, which is applied to carrying control of coal powder in smelt blast furnace gushing coal system. Type W denotes body material seal, which is applied to carrying control of dust powder in removing dust system.

 

性能参数:

Performance parameter:

公称压力

Nominal pressure

0.4MPa

适用温度

Suitable temperature

80150

密封试验压力

Seal test pressure

0.44MPa

强度试验压力

Strength test pressure

0.6MPa

适用介质

Suitable medium

含煤气尘灰、烟气尘灰煤粉等干燥细粉物料

Dust with coal gas and smoke, dry powder

 

工作原理:

Working principle:

手动钟形卸灰阀利用力矩平衡的方法实现卸灰。当作用于锥形塞上的物料产生的力矩大于重锤摇杆产生的力矩时,锥形塞打开向下卸灰。一旦积灰卸去后,重锤与摇杆产生的力矩使锥形塞迅速关阀。落料的频率及卸灰量依据工况需要来调整重锤位置。

执行机构得到程序指令后推动摇杆使锥形塞打开向下卸灰,积灰卸去后,依据程序规定时间,推杆推进使锥形塞关闭密闭。执行机构的推出与推进都有行程控制,同时反馈开关信号。

The valve realizes discharging using trimming moment. When the moment made by material on cone plug is greater than that of heavy hammer and rocker, the plug will open adown to discharge. After discharge the moment made by heavy hammer and rocker will drive cone plug close quickly. Dropping material frequency and discharge amount is determined by the working condition demand to adjust heavy hammer position.

Actuator drives the rocker after receives program order, and the rocker drives the plug open adown to discharge dust. Draw stem drives the plug to close according to the program time after discharge. Push and extrusion of actuator are controlled by journey and feed back switch signal at the same time.

XH--- X W系列外形连接尺寸:

Appearance joint dimension:

DN

200

250

300

350

400

450

500

600

700

800

D

370

420

480

530

620

670

720

835

935

1055

D1

330

380

440

490

570

620

670

780

880

990

D2

280

330

380

430

500

550

600

700

800

900

D3

390

440

500

550

650

700

750

865

965

1083

D4

350

400

460

510

600

650

700

810

910

1020

D5

240

290

340

390

450

500

550

650

750

850

H

350

400

450

500

550

600

640

680

730

760

H1

480

530

580

630

680

730

770

810

860

890

L1

755

805

855

925

975

1025

1075

1275

1375

1475

L2

740

790

840

910

960

1010

1060

1200

1300

1400

n-d

8-Φ18

12-Φ18

12-Φ22

12-Φ22

16-Φ22

16-Φ22

20-Φ22

20-Φ26

24-Φ26

24-Φ30

电动推杆

Electric draw stem

DTA25-M

P0.025kw

DTA63-M

P0.06kw

DTA100-M

P0.25kw

气动推杆

Pneumatic   draw stem

10A-5TCC32B

10A-5TCC40B

10A-5TCC50B

 

使用说明:

Operation instruction:

l  安装时请注意闸门本体上标明介质流向,清除内腔附着物。两法兰连接时必须加密封垫片,然后均匀锁紧螺栓。

l  设备在运行时,请定期给传动部分加润滑油。执行部分定期维护和检修。

l  若长期存放应使设备处于关闭状态,各传动部位加润滑油,不允许露天存放或堆置。

l   Pay attention to the direction of medium in valve body. Clean the inner body. Add seal cushion between two flanges connection and screw down bolt

l   Please add lubricant to transmission when equipment is operating and maintain and check the actuator regularly.

l   Add lubricant to transmission part when valve is long stored. It should not be placed or piled up in the open air.


湖北澳恒环保设备有限公司 版权所有

备案号: 鄂ICP备14001966号-1

地址:湖北省荆州市沙市区王家港路53号 电话:0716-4310982 传真:0716-4310980